Standing Seam Roofing
Benefits
Storm Proof Performance
Seam to seam locks and high strength clips protect against Texas weather extremes—hurricane force winds, heavy hail, and driving rain—far surpassing asphalt shingles, wood shakes, or concrete tile.
Sleek Modern Appeal
Distinct vertical ribs deliver a clean architectural profile that elevates everything from modern builds to luxury renovations. Choose from matte, metallic, or textured finishes in a wide palette of designer colors.
Energy Efficiency & Sustainability
Cool roof PVDF coatings reflect intense solar heat, lowering attic temperatures and trimming air conditioning costs during triple digit Texas summers. Made from 100 percent recyclable steel, standing seam roofing is an environmentally responsible choice.
Low Maintenance Longevity
Factory applied paint systems resist chalking, fading, and corrosion, while concealed fasteners eliminate exposed screws that can loosen or rust. Enjoy decades of protection with little more than an occasional rinse.
Lightweight Quick Installation
At roughly 1.5 pounds per square foot, standing seam roofing is lighter than tile or slate, easing structural load and enabling faster, less disruptive installation—often directly over existing decking.
Standing-seam metal roofing delivers a modern, streamlined look while harnessing the full strength of galvanized or Galvalume® steel. Continuous panels lock together with concealed fasteners, creating a watertight barrier that shrugs off high winds, heavy rain, and rooftop debris. Finished with high-performance PVDF paint systems, these roofs resist fading, corrosion, and impact, offering decades of low-maintenance protection and contemporary curb appeal.
By choosing standing seam roofing, you gain hurricane rated strength, energy saving efficiency, and a sleek modern look that boosts curb appeal and resale value, all purpose built to thrive in the toughest Texas climate.
Material Options
Aluminum
Sleek, Coastal-Ready Protection
Standing seam aluminum roofing delivers the crisp vertical lines architects love and the all-weather muscle Gulf Coast homes demand. Continuous aluminum panels lock over concealed clips, creating an uninterrupted metal surface that resists salt spray, hurricane-force winds, and pounding hail—all at a fraction of the weight of tile or even steel panels. Choose from a spectrum of high-performance PVDF colors that stay vibrant decades longer than conventional paints.
Key Features
- Concealed-fastener system for a clean, minimalist profile
- Snap-lock or mechanically seamed ribs that seal out wind uplift and wind-driven rain
- Ultra-lightweight—under 50 lb per square, easing structural load and simplifying transport
- Naturally rust-proof aluminum ideal for coastal and high-humidity regions
- Approved for direct-to-deck installation to speed up projects and cut labor costs
Steel
Powered by Central States + Sherwin-Williams
Key Features
- Concealed-fastener seams for a sleek, uninterrupted roofline
- Snap-lock or mechanically seamed ribs that exceed hurricane-zone wind-uplift codes
- Class 4 impact rating resists hail better than asphalt, tile, or wood shakes
- Lightweight—approx. 100 lb per square, easing structural load and simplifying transport
- Cool-Roof color palette from Sherwin-Williams Fluropon® keeps attics cooler and slashes A/C costs
- Suitable for direct-to-deck installation to cut labor time and material waste
Partnering with Central States® Manufacturing and Sherwin-Williams Coatings, we deliver standing-seam steel panels that arrive at your site ready for precision installation—no field cutting, no on-site painting. Central States roll-forms each panel to exact length, then Sherwin-Williams applies a high-performance PVDF finish in a climate-controlled facility. The result is a roof with flawless color consistency, superior corrosion resistance, and zero overspray mess on your property.
Standing Seam Portfolio
Factory vs On-Site Fabrication
| Benefit | Factory Fabrication | On-Site Fabrication |
|---|---|---|
| Coating Quality | 70% PVDF baked on at optimal temperature for long-term gloss retention | Air-dry paints prone to runs, fading, and uneven coverage |
| Color Consistency | Continuous coil coating—every panel matches | Shade variation from weather, humidity, or mixed batches |
| Weather Window | Panels arrive finished; install in any season | Delays if wind, dust, or rain prevent painting |
| Environmental Impact | Zero VOC emissions on your property | Overspray, masking, and cleanup required |
| Project Speed | Panels lock in place the same day they’re delivered | Extra days for priming, painting, and curing |
Color Options
Steel Coated Partners
Steel Warranty Highlights
| Warranty Tier | Covered Products & Coating | Length & Key Metrics | What’s Actually Protected |
|---|---|---|---|
| Lifetime Ultra SMP | Standing-seam & exposed-fastener panels finished in Ultra-grade silicon-modified polyester (SMP) | Lifetime against crack/peel; fade ≤ 5 and chalk ≤ 8 for 30 yrs | Paint adhesion, color stability, chalk resistance |
| Lifetime Prime Fluropon® (PVDF) | Premium CentralGuard® panels with Sherwin-Williams 70 % PVDF coil coating | Lifetime adhesion + 30 yr fade/chalk (roof & wall: fade ≤ 5, chalk ≤ 8) | Highest gloss retention; coastal installs allowed if > 1 500 ft from salt water |
| Lifetime Prime SMP | Prime SMP colors (non-textured) | Same coverage term & limits as Ultra SMP | Equal to Ultra but limited color palette |
| 40-Year Standard SMP | Standard SMP colors on Panel-Loc Plus®, R-Loc®, etc. | 40 yrs adhesion, 30 yrs fade/chalk | Budget line for agricultural & residential use |
| 20-Year Copper Metallic & Thrifty SMP | Specialty metallic or economy finishes | 20 yrs adhesion, 20 yrs chalk; no fade guarantee on Copper Metallic | Short-term projects & accent panels |
Visit Central States for more warranty information – Click Here
Aluminum vs Steel
| Benefit | Marine-Grade Aluminum (factory-fabricated panels) |
Galvalume / Steel (typical on-site fabrication) |
|---|---|---|
| Corrosion / Rust | Aluminum cannot rust—perfect for coastal & high-salt zones. | Red-rust creep possible; cut edges are vulnerable from day one. |
| Coastal Warranty | 50-yr substrate + 35-yr PVDF finish within 1 mile of shoreline. | Many warranties prorate or void inside 1,500 ft of salt water. |
| Weight & Structure | ≈ 0.7 lb / ft² (about ⅓ the weight of steel) — often no framing upgrade. | ≈ 2.0 lb / ft² — heavier load can require extra rafter or purlin support. |
| Paint Quality | 70 % PVDF baked on at the mill; no under-film rust to blister coating. | Same finish available, but if coating chips, rust undercuts the paint. |
| Project Speed | Panels arrive finished & cut to length — install as soon as delivered. | Extra job-site time for coil loading, forming, cutting & handling. |
| Energy Reflectivity | “Cool-roof” pigments reflect up to 0.70 solar reflectance (SR). | Similar colors, but higher thermal mass means slower night-time cooling. |
| Sustainability | 100 % recyclable; high scrap value keeps material out of landfills. | Recyclable, but lower scrap value can reduce recovery rates. |
Standing Seam FAQ
What is standing seam metal roofing and how is it different from other metal panels?
Standing seam is a premium metal roofing system featuring continuous panels that run from ridge to eave with raised vertical seams (ribs). Clips or concealed fasteners lock the panels to the deck so no screws penetrate the weather surface. In contrast, exposed-fastener roofs (e.g., R-panel or corrugated) rely on visible screws through the panel, which can loosen or leak over time. Standing seam delivers a cleaner look, built-in expansion tolerance, and superior long-term weather resistance—ideal for homeowners seeking both performance and modern aesthetics.
How long will a standing seam roof last in Texas?
With 24- or 26-gauge Galvalume® steel and a high-performance PVDF (Kynar 500®) paint finish, a standing seam roof routinely lasts 40–70 years in Texas. The alloy coating resists rust, while the paint blocks UV degradation even in Houston’s intense sun. Periodic inspections and simple maintenance (leaf removal, gutter cleaning) will help the roof easily outlive asphalt shingles by two to three life cycles.
Is a standing seam roof loud during rain or hail?
No. When installed over solid decking, synthetic underlayment, and attic insulation, a standing seam roof is only marginally louder than architectural shingles. Many owners say the sound is a pleasant, muted patter. Optional high-temp peel-and-stick underlayments or acoustic boards can further dampen noise if desired.
How does standing seam perform in hurricanes and high winds?
Properly installed standing seam systems are tested to ASTM E 1592 and can resist uplift pressures equivalent to 140+ mph winds. RISE Roofing uses engineered clips, stainless fasteners, and 16-inch or narrower panel widths to meet Texas Department of Insurance (TDI) windstorm requirements along the Gulf Coast.
Are standing seam roofs energy-efficient in hot climates?
Yes. Cool-roof PVDF colors reflect solar radiation and re-emit heat, lowering attic temperatures by 20–30 °F compared with dark shingles. Many colors carry an ENERGY STAR® or CRRC rating and may qualify for local utility rebates. When combined with proper attic ventilation, homeowners frequently report 10–15 % reductions in summer cooling costs.
How much does standing seam cost compared to shingles or tile?
Installed pricing in Texas typically ranges from $9 to $13 per square foot, depending on gauge, panel profile, and roof complexity. That’s 2–3 × more than dimensional shingles but 20–40 % less than clay or slate tile. Because a standing seam roof can last 60 years or more with minimal upkeep, its lifetime cost is often lower than repeating shingle replacements.
Will a standing seam roof boost curb appeal and resale value?
Absolutely. Its sleek, uninterrupted lines create a contemporary yet timeless aesthetic that photographs beautifully for listings. Appraisers often credit metal roofs for longevity, impact resistance, and insurance savings—attributes that attract buyers and can increase resale value.
What warranties are available?
Most panel manufacturers provide a 40- to 45-year PVDF paint warranty against fading and chalking plus a 25-year substrate (Galvalume) corrosion warranty. As a Central States® and McElroy Metal® partner, RISE Roofing adds a lifetime workmanship warranty covering installation defects for as long as you own your home.
How long does installation take?
For an average 2,500 sq ft home, tear-off and installation require about 3 to 6 working days. Complex roofs with numerous valleys or custom flashing can extend the schedule a few days. We handle permits, material delivery, daily cleanup, and final inspection to keep the process smooth and timely.
Can my insurance policy help pay for a standing seam upgrade?
If your existing roof has qualifying hail or wind damage, your carrier may pay to replace it with “like kind and quality.” Many policies allow you to apply that payout toward an upgrade—you’d pay only the difference. RISE Roofing documents damage, meets with the adjuster, and supplies code-compliant estimates so you can make an informed decision.
Be sure to check out Stone Coated Steel Roofing and other Metal Roofing alternatives.
Standing Seam Professionals
Request a Callback
We understand your busy schedule, so we make getting a new standing seam roof a stress free process.
Over our 10 minute call — we’ll discuss any specific roofing requests, style, and color options. After the call we’ll send you all the information we discussed to assist with decisions.
48-72 hours we’ll hand deliver or email a free, no-obligation, price-locked quote.
Click the button below to schedule a call and get started today!